How-to foutcodes uitlezen

Doe het zelf instructies en uitleg

How-to foutcodes uitlezen

Berichtdoor Raymond » 21 Jan 2012, 19:53

Hierbij een uitleg hoe je je ecu kan uitlezen op foutcodes.

Om je ecu te kunnen uitlezen moet je eerst de uitlees stekker vinden, Deze zit boven je ecu in een rubbere groene beschermhoesje.
Als je die heb gevonden pak je de stekker die 2-draads is, in die stekker steek je een geleidend iets in bijv. een paperclip.
Wel zorgen dat het goed contact maakt anders doet het niets.
Dan kan je gaan beginnen met uitlezen, dit doe je door de auto op contact te zetten.
Als je een foutcode hebt zal het motorlampje een knippercode geven, als je geen foutcode heb zal het lampje aan blijven staan.

Hieronder een lijst met foutcodes. Een korte knipper betekent 1 en een lange knipper betekent 10.

1 Oxygen Sensor "A" (Primary) defective circuit or unplugged / defective sensor
2 Oxygen Sensor "B" defective circuit or unplugged / defective sensor
3 Manifold Absolute Pressure (MAP Sensor) defective circuit or unplugged / defective sensor
4 Crankshaft Angle Sensor (CAS) defective circuit or unplugged / defective sensor
5 Manifold Absolute Pressure (MAP Sensor) mechanical problem / disconnected piping
6 ECT Sensor (Engine Coolant Temperature) defective circuit or unplugged / defective sensor
7 Throttle Position Sensor (TPS) defective circuit or unplugged / defective sensor
8 TDC Position (Top Dead Centre Sensor) defective circuit or unplugged / defective sensor
9 CID Sensor (Number 1 Cylinder position) defective circuit or unplugged / defective sensor

10 IAT Sensor (Intake Air Temperature) defective circuit or unplugged / defective sensor
11 CO pot
12 EGR Lift Sensor (Exhaust Gas Recirculation) defective circuit or unplugged / defective sensor
13 APS Sensor (Atmospheric Pressure Sensor) defective circuit or unplugged / defective sensor
14 IAC/ISCV Valve (Idle Air Control/Idle Speed Control Valve) defective circuit or unplugged / defective sensor
15 Ignition Output Signal missing or defective ignition output signal
16 Fuel Injector System defective circuit or unplugged / defective fuel injector
17 VSS (Vehicle Speed Sensor) defective circuit or unplugged / defective sensor
18 Ignition Timing
19 Automatic Transmission Lock Up Control Solenoid Valve defective circuit or unplugged / defective solenoid valve

20 Electrical Load Detector (ELD)
21 VTEC Solenoid Valve defective circuit or unplugged / defective solenoid valve
22 VTEC Oil Pressure Switch defective circuit or unplugged / defective oil pressure switch
23 Knock Sensor (KS) defective circuit or unplugged / defective sensor

30 Automatic Transmission Signal: "A" / SEAF / SEFA / TMA or TMB
31 Automatic Transmission Signal "B"
35 TCSTB signaal. (TCS)
36 TCFC signaal. (TCS)

41 Primary Oxygen Sensor – Heater circuit malfunction on D16Z6, D16Z7 and B16A2 engines
41 Linear Air Flow (LAF Sensor) heater malfunction on D15Z1 engine
42 Lambda 2 – Storing in verwarming
43 Fuel Supply System - Storing in brandstoftoevoer of Lambda sonde 1
44 Fuel Supply System - Storing in brandstoftoevoer of Lambda sonde 2
45 System Too Lean or Too Rich malfunction in the fuel monitoring systems
47 Spanning brandstofpomp
48 Linear Air Flow (LAF Sensor) defective circuit or unplugged / defective sensor

51 Magneetventiel VTEC (achter)
52 Oliedrukschakelaar VTEC (achter)
53 Pingelsensor achter.
54 CKF Sensor (Crankshaft Speed Fluctuation) krukstandsensor
58 BDP Sensor 2 (Bovenste Dode Punt)
59 BDP sensor 2 (Bovenste Dode Punt) Cilinder 2

61 Oxygen Sensor, Heated - Sensor 1 (Primary) high voltage, low voltage, or slow response
63 Oxygen Sensor, Heated - Sensor 2 (Secondary) high voltage, low voltage, or slow response
65 Oxygen Sensor Heater (Secondary) malfunctioning or defective oxygen sensor heater
67 Catalyst system Efficiency Below Threshold malfunctioning or defective catalyst system

70 Automatic Transmission malfunction with the automatic transmission controls
71 Cylinder 1 Misfire or a Random Misfire a condition is present that is creating a cylinder misfire
72 Cylinder 2 Misfire or a Random Misfire a condition is present that is creating a cylinder misfire
73 Cylinder 3 Misfire or a Random Misfire a condition is present that is creating a cylinder misfire
74 Cylinder 4 Misfire or a Random Misfire a condition is present that is creating a cylinder misfire
75 Cylinder 5 Misfire or a Random Misfire a condition is present that is creating a cylinder misfire
76 Cylinder 6 Misfire or a Random Misfire a condition is present that is creating a cylinder misfire

80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem

90 Evaporative Emission Control System leak detected in the fuel tank area
91 Fuel Tank Pressure Sensor low input.
92 Evaporative Emission Control System insufficient purge flow

Gebruikers-avatar
Raymond
HCN Groupie
HCN Groupie
 
Berichten: 5886
Geregistreerd:
06 Mei 2007, 11:02
Woonplaats:
Leiden, Zuid-Holland NL

Re: How-to foutcodes uitlezen

Berichtdoor djkruijt » 01 Mrt 2012, 15:55

Hoe kan het dan dat ik bij mij B18c storing:
41 Primary Oxygen Sensor – Heater circuit malfunction on D16Z6, D16Z7 and B16A2 engines
41 Linear Air Flow (LAF Sensor) heater malfunction on D15Z1 engine

Krijg? Iemand hier een antwoord op. Mn waardes zijn te hoog voor APK namelijk..

djkruijt
HCN Regular
HCN Regular
 
Berichten: 489
Geregistreerd:
09 Okt 2009, 07:42
Woonplaats:
Almere

Re: How-to foutcodes uitlezen

Berichtdoor Raymond » 01 Mrt 2012, 16:01

Je eerste verwarmde lambda kaduk?

Gebruikers-avatar
Raymond
HCN Groupie
HCN Groupie
 
Berichten: 5886
Geregistreerd:
06 Mei 2007, 11:02
Woonplaats:
Leiden, Zuid-Holland NL

Re: How-to foutcodes uitlezen

Berichtdoor djkruijt » 02 Mrt 2012, 09:49

Ik heb maar 1 lambda

djkruijt
HCN Regular
HCN Regular
 
Berichten: 489
Geregistreerd:
09 Okt 2009, 07:42
Woonplaats:
Almere

Re: How-to foutcodes uitlezen

Berichtdoor Raymond » 02 Mrt 2012, 13:05

Klopt en die is 4 draads als het goed is?

Gebruikers-avatar
Raymond
HCN Groupie
HCN Groupie
 
Berichten: 5886
Geregistreerd:
06 Mei 2007, 11:02
Woonplaats:
Leiden, Zuid-Holland NL

Re: How-to foutcodes uitlezen

Berichtdoor djkruijt » 02 Mrt 2012, 14:22

Yess, 4 draads ja!

djkruijt
HCN Regular
HCN Regular
 
Berichten: 489
Geregistreerd:
09 Okt 2009, 07:42
Woonplaats:
Almere


Terug naar How to



Wie is er online?
Gebruikers in dit forum: Geen geregistreerde gebruikers en 32 gasten
cron